Your Bump Key Attempts
27 posts
• Page 1 of 2 • 1, 2
let's see your home brew bump key attempts, if their a complete success or about as good as a glass hammer, we want to see them
Re: Your Bump Key Attempts
well here are a few of mine.
oh and here are a few other links to the other files i have in my album...
http://i62.photobucket.com/albums/h109/ ... 7_1835.jpg
http://i62.photobucket.com/albums/h109/ ... 7_1838.jpg
http://i62.photobucket.com/albums/h109/ ... 7_1841.jpg
http://i62.photobucket.com/albums/h109/ ... 7_1842.jpg
oh and here are a few other links to the other files i have in my album...
http://i62.photobucket.com/albums/h109/ ... 7_1835.jpg
http://i62.photobucket.com/albums/h109/ ... 7_1838.jpg
http://i62.photobucket.com/albums/h109/ ... 7_1841.jpg
http://i62.photobucket.com/albums/h109/ ... 7_1842.jpg
Re: Your Bump Key Attempts
Manually made with a P-X23MC cutter and the first cut from shoulder is is skewed towards the tip by 0.1 to 0.15" from the factory spec 0.231, which has the same effect as filing down the shoulder
Re: Your Bump Key Attempts
usmcboltaction wrote:Hey Josh, I made a tension wrench like the one in your pics last night. It works great! I am kinda pissed at myself for not thinkin of something like that.
haha and it took me a whole 7 seconds to think it up.
Re: Your Bump Key Attempts
1st attempt and it works(2 spool drivers)
Re: Your Bump Key Attempts
very nice attempt, what lock you using with it?
Re: Your Bump Key Attempts
Its for a Yale Cylinder (2 spool drivers). Gonna try and make one for my Abus 85/70 if i can find out pin spacing dimensions
Re: Your Bump Key Attempts
sounds great, josh has a link here somewhere on where to find spacings. i'm sure you'll get it worked out.
Re: Your Bump Key Attempts
well the site i guess was taken down, or at least one of them was... but here is a pdf printout made by ezpicker over at ezp... he was smart enough to print it before the site closed...
--edit---
i guess it didnt attach, so here is the link
--edit---
i guess it didnt attach, so here is the link
Re: Your Bump Key Attempts
yeah it dosent accept PDF, if any of you want to upload a raw PDF then put it in a zip folder.
Edit: .PDF is now enabled, you no longer have to put it in a zip folder, you may upload the raw file.
Lew
Edit: .PDF is now enabled, you no longer have to put it in a zip folder, you may upload the raw file.
Lew
Re: Your Bump Key Attempts
oh well. its not that important... the link works...
Re: Your Bump Key Attempts
Thanks for that Josh
Re: Your Bump Key Attempts
I checked out that pdf but it doesn't have Abus on the list, I noticed that the average center to center dimensions are 0.156" is this dimension a safe bet to go for or are the center to center dimensions more critical from lock to lock for bump keys?
Edit: I've had a think about it and that question sounds stupid What I think I'm trying to say is: Is there any +/- tolerance when making bump keys. I hope thats a bit clearer
Edit: I've had a think about it and that question sounds stupid What I think I'm trying to say is: Is there any +/- tolerance when making bump keys. I hope thats a bit clearer
Re: Your Bump Key Attempts
here are a few abus sheets
You do not have the required permissions to view the files attached to this post.
Re: Your Bump Key Attempts
Ta Josh
27 posts
• Page 1 of 2 • 1, 2
Who is online
Users browsing this forum: No registered users