Page 1 of 2

Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 2:46 am
by MrPharmer2012

http://www.youtube.com/watch?v=BIvV1Fk7BHY
I have this lock picked it open unsure of how to tear down and find key blank and make a key, if i remove set screw and pull cylinder the top pins and springs will fall out how would i hold those in chamber and reinsert core? If i did this, please send me recommendations on how to get a key for this the side has a serial number on it can i order a key?

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 3:02 am
by MrPharmer2012
I can’t get pics to attach or the video link to work

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 3:18 am
by Riyame
Long time no see man, how is it going?

I should have fixed the youtube imbed for you, it can be wonky sometimes, and you can't link photobucket pics any more unless you pay them $00 a year so most of us use imgur.com now or upload them right to the site.

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 5:06 am
by MrPharmer2012
Everything has been great been super busy but recently pulled some locks back out and getting the bug back, i am a little rusty but it is coming back, I love this site and have learned a lot from it over the years a lot of good guys on here

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 5:08 am
by MrPharmer2012
Riyame any idea on where i can get keyblanks or know where can get info on this or send it off for a key to be made?

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 7:32 am
by Riyame
Were these the ones that were in the big lot on ebay for cheap a year or 2 back? I am not sure if anybody has been able to get keys, I thought that it was a restricted keyway.

You would likely have better luck asking on an EU forum.

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 8:50 am
by MrPharmer2012
Curiosity got to me I had to know what was in it I opened it up, now i will be tasked with reassembly somehow

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 8:52 am
by MrPharmer2012
Spools and barrels every chamber

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 10:41 am
by femurat
I see an interesting pins selection in that padlock. Lucky you, there are many master wafers, otherwise a "rusted" picker would have struggled quite a bit to open it.

Welcome back :)

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 12:10 pm
by mdc5150
20180220_050826.jpg
Is this the same keyway? If not can you send a clear pic of the keyway? I might be able to since I made one for my oval.

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 4:28 pm
by MrPharmer2012
My keyway the top bends other way looks like, any suggestions for reassembly when if i get key made? Do the plugs on the side push all the way thru and are they reusable? Or do i have to pin from inside and use like the Peterson topload kit

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 4:40 pm
by MrPharmer2012
Here is a better keyway pic, what would be cool is to find someone with a mill and have this turned into a cutaway and on each one of the stacks drill and tap them with set screws to add to the fun so you could easily change pins out to make it more fun anyone with ideas for keys and or experience making a cutaway let me know just a few thoughts running in my head

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 4:46 pm
by MrPharmer2012

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 8:04 pm
by Riyame
Fixed your video link. Remove the S from the HTTPS and use the full youtube link instead of the shortened one.

Anarchy_won has a mill and makes cutaways but it usually takes times.

One way to reassemble it if possible is to get a thin piece of metal that fits into the bottom of the keyway. You then form it into a clip t hat bends up along the bottom of the lock and again to go along the side. This will be used to hold all the top pins into place. Then you slide in the plug upside down then turn it while slipping off the metal clip. Then you pull out the clip and reinstall the bit that holds the plug into place.

Re: Help- Does anyone have capability to make trioving key

PostPosted: Tue Feb 20, 2018 9:58 pm
by lock-ed
MrPharmer,
that is a restricted keyway. You will have trouble getting a key made, or obtaining a blank.

On the positive side,- yes the code on THIS padlock can be used to ID blank/cuts. However, you need to track down the locksmith that has the licence for your particular code.

Had it been the standard(508) profile, I could have sent you blanks straight away.

Sorry I couldn't help more, but good lock-luck! :salute:

Rgds,
Ed