Page 1 of 1
I Need a Key Cut to Code Please
Posted:
Wed May 07, 2014 10:56 am
by mister sour
I have this super rare Yale Dual Custody Bicentric padlock. I have the Guard keys (Guard, not Master) but I dont have the change keys. I SUCK at impressioning. I need to practice but I dont want to strip the warding of the key way or abuse this lock in any way. Can someone help? On the plug there is a stamped code. Perhaps this will render key cuts in code source or create a key? I will pay for the keys you make me plus shipping. The key blank I would need cut is a Yale small pin Y54. If you anyone can do this on factory embossed yale key blanks, I will be so grateful. Brass Ilco blanks will do to.
Re: I Need a Key Cut to Code Please
Posted:
Wed May 07, 2014 11:20 am
by jeffmoss26
Are you sure the blank is Y54? Small pin tumbler is normally Y52.
Re: I Need a Key Cut to Code Please
Posted:
Wed May 07, 2014 11:51 am
by mister sour
These keys fit perfectly into the change cylinder.
Re: I Need a Key Cut to Code Please
Posted:
Wed May 07, 2014 1:47 pm
by jeffmoss26
My bad, Y54 is also a small keyway. I just see Y52 most of the time.
Re: I Need a Key Cut to Code Please
Posted:
Wed May 07, 2014 6:30 pm
by macgng
Yale Pin Tumbler padlock: Small Pin.
Cuts: 22264
HPC120CMB card: C57
Re: I Need a Key Cut to Code Please
Posted:
Wed May 07, 2014 6:54 pm
by mister sour
macgng wrote:Yale Pin Tumbler padlock: Small Pin.
Cuts: 22264
HPC120CMB card: C57
Weird. Jeff said it was 33375. I appreciate the both of you. I will give em both a try. Thank you.
Re: I Need a Key Cut to Code Please
Posted:
Wed May 07, 2014 7:06 pm
by macgng
thats what code source says it is. whatever works.
Re: I Need a Key Cut to Code Please
Posted:
Wed May 07, 2014 7:32 pm
by GWiens2001
If you can cut it yourself, cut the 22264 first. If it does not work, then cut it to 33375. Sometimes there are different bittings depending on which code set it is.
Gordon
Re: I Need a Key Cut to Code Please
Posted:
Thu May 08, 2014 5:36 am
by jeffmoss26
I looked it up in a 1978 Reed's code book. Not sure which one is more likely to be correct.
Re: I Need a Key Cut to Code Please
Posted:
Thu May 08, 2014 10:56 am
by 10ringo10
The cut sheet is already up on the bicentric i posted it years back sour ! macgng is correct on code use the small key
just checked its still up the silca ya3r blank topic by mr pharmer ( who bought osu yale bicentric from imschatten )
Re: I Need a Key Cut to Code Please
Posted:
Sat Jun 14, 2014 1:46 pm
by mister sour
Big shout out to Jeffmoss26 and Macgng for supplying me with codes. Turns out, 33375 was correct! I appreciate it guys.
Re: I Need a Key Cut to Code Please
Posted:
Sat Jun 14, 2014 1:51 pm
by flywheel
That is an awesome lock! Who needs LOTO when you can have that beauty?
Re: I Need a Key Cut to Code Please
Posted:
Sat Jun 14, 2014 6:33 pm
by GWiens2001
Sour, that is an intensely drool-worthy lock! Have been looking for a Yale bicentric lock for a while. Someday.
Gordon