Page 4 of 5

Re: Pin Modification

PostPosted: Mon Sep 01, 2014 8:44 am
by femurat
Thanks for the picture FarmerFreak, I thought it was upside down... :)

Re: Pin Modification

PostPosted: Mon Sep 01, 2014 9:41 am
by flywheel
FF's picture shows the correct orientation.

Before sending a couple challenge locks out I beta tested two (only two!) pins in chambers 3 and 4 of a mortise cylinder. I panicked for a minute thinking I had just locked myself out of the cylinder I had intended to use. The non-stop springy feedback really threw me for a loop. Until you get the deep false set on the inner pins it's very difficult to know if you are proceeding down the right path. Now multiply this by 5 or 6 pins!

Hats off to rerun12 and Farmerfreak for successfully opening their locks. Incredible!
Huzzah!

Re: Pin Modification

PostPosted: Mon Sep 01, 2014 5:24 pm
by GWiens2001
flywheel wrote:This was before they fell into the wood chipper...
2014-08-02 09.40.40.jpg


By the way, wood chippers are great for pin modification.


It has been a while, but thought I should post of what that particular LFIC looked like after the 'wood chipper' treatment. But first, in typical 'me' fashion, gotta tell it in stages.

Fifth, ended up with this...

Image

Oh, wait. MIssed a few picking stages there, didn't I? :oops:

With the first 'set', it looked like this.

Image

The next set was deeper. Gotta be a false set. A tiny bit more work with the pick, and got here!

Image

OK, now to get out of that false set. Here we go! Yeah... another false set... deeper yet.

Image

More picking, and WTF? How deep a false set can you get??? :shock:

Image

Another five minutes with the pick, and still not a single pin is budging. No counter rotation at all. No spring at all. :evil: :evil:

Oh... uhhh... :oops:

Image

LFIC. Picked to control. :oops:

OK, pushed the control tab back out, and we are back to the first picture.

Image

Much better. Yeah, I meant to do that. Knew it was at control the whole time. (You do believe me, don't you?) :roll:

OK, what is inside? Dumped the pins into this nifty Keypicking.com pinning tray (3D printed by Anarchy_won).

Image

And the pins are beautiful.

Image

Bit of an improvement from the original at the top of this post, isn't it?

Suggested improvement - countermilling or threading the pin channels to catch those beautiful stepped spool pins.

This was a fun pick, and caught my attention primarily because of deeper and deeper false set. After three progressively deeper false sets, thought control was yet another false set. Appreciate the fun, Flywheel.

Gordon

Re: Pin Modification

PostPosted: Mon Sep 01, 2014 6:21 pm
by flywheel
After picking open the first time, and thinking it was too easy, I decided to give the long serrated pins a slight taper so there would be more intermediate T-pin binding.

Besides being in great shape, that LFIC is the only one I've come across so I was reluctant to thread the chambers without the proper tools.

All in all a fun pick with all the sharp clicks and never ending false sets. Glad you enjoyed it!

Re: Pin Modification

PostPosted: Mon Sep 01, 2014 6:34 pm
by jeffmoss26
Oooh nice pinning! I like the tray too!

Re: Pin Modification

PostPosted: Sat Nov 22, 2014 9:33 am
by Doogs
Damn Fly:
I can't believe I'm just finding this thread now. I love those PiP using nails I usually just bang nails into wood! I never thought of them as lock components. Maybe I can re-purpose some stuff kicking around also , although I'm not nearly as creative as some of my fellow KPer's. The ingenuityy here amazes me.

So many challenges so little time. I need to get my shed done and tools setup so I can go out there and get lost in locksmithery for hours at a time.

Great work Mate.

Re: Pin Modification

PostPosted: Mon Dec 01, 2014 12:27 pm
by Papa Gleb
Flywheel you have out done yourself friend. I have collected several tiny screws to used a pins for challenge locks but the pin-in-nailpins are AMAZING. Im just super amazed WOW great work bud.

If that pin-in-nailpin lock is still around, I would love to take a stab at it. thanks

Re: Pin Modification

PostPosted: Mon Dec 01, 2014 7:25 pm
by Farmerfreak
Papa Gleb wrote:If that pin-in-nailpin lock is still around, I would love to take a stab at it. thanks
The one that was sent to me got passed along to Xeo. I don't know if he has tried to pick it yet or if it has been sent to someone else.

Re: Pin Modification

PostPosted: Wed Apr 01, 2015 10:55 am
by flywheel
Nothing new. Here are the challenge lock pins I sent to bosnianbill a couple weeks ago. I was really nice and gave him a wide open keyway and gentle bitting. The driver and key pins are not paired properly and the final order differs also.
2015-03-22 01.19.31 copy.jpg


Here is the plug before reassembly. This is what BB will have to pick through.
2015-03-22 11.27.36.jpg


Here we go. This is the final order with pin one on the right and six on the left.
2015-03-22 11.22.10.jpg

Re: Pin Modification

PostPosted: Wed Apr 01, 2015 2:58 pm
by VancouverSpecial
flywheel wrote:Nothing new. Here are the challenge lock pins I sent to bosnianbill a couple weeks ago. I was really nice and gave him a wide open keyway and gentle bitting. The driver and key pins are not paired properly and the final order differs also.
2015-03-22 01.19.31 copy.jpg


Here is the plug before reassembly. This is what BB will have to pick through.
2015-03-22 11.27.36.jpg


Here we go. This is the final order with pin one on the right and six on the left.
2015-03-22 11.22.10.jpg


Holy Mother of God! :shock:
Flywheel, you've done some nice work there, those look incredible.

So basically nothing but misleading feedback from the top row? Have you had any success picking them? Any hints?
Can't wait to see the video, well that is if Bill can figure out how to pick it that is :razz:

Thanks for the pin porn - quite inspiring really - DIY rocks!
Cheers,
Sean

edit - for brain malfunctions....cccannnt ttttypppe....

Re: Pin Modification

PostPosted: Wed Apr 01, 2015 6:31 pm
by Oldfast
*shakes his head* WICKED BEAUTIFUL.

I haven't been keeping up on the tube lately....
but I may have to keep an eye out for Bill's vid. lol

In fact, if you remember... post the link to it here when it comes out will you?

Re: Pin Modification

PostPosted: Thu Apr 02, 2015 10:54 am
by flywheel
I was contacted via YT by someone asking for a challenge lock swap. I was happy to help and sent him some standard stuff. Should be arriving on his doorstep today.
2015-03-29 16.58.07 copy.jpg

One little nasty trick though. Pin 4 is already at the shear line. It will be overset if lifted at all. After this picture was taken I knocked a few thousandths off the diameter to help facilitate oversetting. Oh, that and the short pin behind it. :mrgreen:
2015-03-29 17.03.48 copy.jpg

This next lock was pinned to a "T". Key pins are serrated as force of habit but I now realize that oversetting them probably isn't a problem with such aggressive T-pins.
2015-03-30 13.32.58 copy.jpg

Most of the alterations rest below the shear line leaving very little slop in the plug.
2015-03-30 13.35.38 copy.jpg

All in all some nice 5-pin distractions.
Have a great day KPers! :pimpmofo:

Re: Pin Modification

PostPosted: Thu Apr 02, 2015 1:42 pm
by Papa Gleb
incredible work man just incredible. If you ever get around to make any more of those pin in pin challenge locks keep me in mind. Ill be more than happy to swap or trade or whatever lol

Re: Pin Modification

PostPosted: Thu Apr 02, 2015 5:34 pm
by VancouverSpecial
GWiens2001 wrote:
Suggested improvement - countermilling or threading the pin channels to catch those beautiful stepped spool pins.

This was a fun pick, and caught my attention primarily because of deeper and deeper false set. After three progressively deeper false sets, thought control was yet another false set. Appreciate the fun, Flywheel.

Gordon



Hey Fellahs,

So, I think I understand how to go about threading the plug with a tap+die setup but countemilling pin chambers has me stumped?

Ideas for how can one countermill the pin chambers in the plug? I'd love to be able to cut a ledge out below the lip (like some of the Scandinavian-made locks often have). My only thought so far is to find a small enough dremel cutting bit with a squared off cylinder shape (not rounded) - but no idea if this would work, plus I haven't yet found the right bit (I have one the right shape but too big).

Keep up the great work Flywheel :)

Sean

Re: Pin Modification

PostPosted: Thu Apr 02, 2015 5:49 pm
by flywheel
VancouverSpecial71 wrote:So, I think I understand how to go about threading the plug with a tap+die setup but countemilling pin chambers has me stumped?

Ideas for how can one countermill the pin chambers in the plug? I'd love to be able to cut a ledge out below the lip (like some of the Scandinavian-made locks often have). My only thought so far is to find a small enough dremel cutting bit with a squared off cylinder shape (not rounded) - but no idea if this would work, plus I haven't yet found the right bit (I have one the right shape but too big).

I've tried with a hand drill and dremel but there is just not enough stability plus standard drill bits only chamfer the edge. Probably need a drill press and bits used for milling.